Roof Replacement Cost Calculator (2026)
Last updated · Prices reviewed
Replacing an asphalt shingle roof on a 1,000–3,000 sq ft home costs about $5,500–$40,600. Enter your home for your own range.
Estimate your roof
Free · no sign-up · results update as you type
26.6° slope
area × 1.118
Typical $15,500, range $10,000–$24,400. National estimate
Estimated replacement cost · Asphalt shingle
$15,500typical
Range $10,000–$24,400
- Materials (approx.)
- $4,900
- Installation labor (approx.)
- $7,300
- Old roof removal 1 layer
- $3,300
Total (typical) $15,500
National estimate
Medium evidence Weakest figure used: the tear-off price (medium).
Prices checked November 2026
- Roof area
- 2,214 sq ft
- Squares (no waste)
- 22.1
- Shingle bundles (incl. 10% waste)
- 74
- Per square installed, before tear-off
- $550
- Every price comes from a named source, with the date we checked it.
- No contact details asked
- An estimate, not a quote
Replacing an asphalt shingle roof on a 1,000–3,000 sq ft home costs about $5,500–$40,600, or about $4.00–$8.00 per square foot installed for asphalt shingles. Roof size, pitch and material decide where your price lands, along with how many old layers come off. Enter your home above for your own range, then compare written quotes from local roofers.
Roof replacement cost by home size
A bigger home means more roof, but pitch and material move the price as much as size does. Roof area below assumes one story, a 6/12 pitch, 10% for overhangs and one old layer removed.
| Home size | Roof area | Squares | Asphalt shingle | Metal |
|---|---|---|---|---|
| 1,000 sq ft | 1,230 sq ft | 12.3 | $5,500–$13,500 | $7,400–$28,300 |
| 1,500 sq ft | 1,845 sq ft | 18.4 | $8,300–$20,300 | $11,100–$42,400 |
| 2,000 sq ft | 2,460 sq ft | 24.6 | $11,100–$27,100 | $14,800–$56,600 |
| 2,500 sq ft | 3,075 sq ft | 30.7 | $13,800–$33,800 | $18,400–$70,700 |
| 3,000 sq ft | 3,690 sq ft | 36.9 | $16,600–$40,600 | $22,100–$84,900 |
Sources: HomeGuide – Asphalt shingle roof cost; This Old House – New roof cost; HomeGuide – Metal roof cost; InterNACHI – Standard Estimated Life Expectancy Chart; Fixr – Asphalt shingles cost (3-tab, architectural, luxury). How we estimate
Cost by roofing material
All cost guides →- Asphalt shingle3-tab and architectural shingles.$4.00–$8.00 per sq ft installedTypical lifespan: 20–35 yearsAsphalt shingle roof cost →
- MetalStanding seam panels and metal shingles.$5.50–$20.00 per sq ft installedTypical lifespan: 40–70 yearsMetal roof cost →
- TileClay and concrete tile.$8.00–$25.00 per sq ft installedTypical lifespan: 50–100 yearsTile roof replacement cost →
- SlateNatural and synthetic slate.$15.00–$35.00 per sq ft installedTypical lifespan: 60–150 yearsSlate roof cost →
- Flat (EPDM / TPO)EPDM and TPO membranes for low-slope roofs.$4.00–$13.00 per sq ft installedTypical lifespan: 7–25 years (limited evidence)Flat roof replacement cost →
What changes the price
Two homes with the same living area can get quite different quotes. These are the main reasons.
Roof size
Roofers price by the square: 100 sq ft of roof surface. Roof area follows the home’s footprint, not its living area, so a two-story home has about half the roof of a one-story home with the same floor space.
Pitch
Pitch is how steep the roof is, written as rise per 12 inches of run. A steeper roof has more surface over the same footprint: about 12% more at 6/12 and 41% more at 12/12. Steep roofs are also slower to work on, so our estimate raises the labor and tear-off part for steep roofs.
Material
The material sets the installed price per square foot. Each material’s range is in the cards above, and the calculator lets you switch between them.
Old layers
Tear-off means removing the old roofing down to the decking. Each layer removed adds labor and disposal, so two old layers cost more to clear than one. Your roofer can tell you how many there are.
Access
A steep driveway, a tight lot, plantings close to the walls or no space for a dumpster make it harder to bring materials in and haul debris out, which can add time to the job.
Region
Labor rates and material prices differ from one area to another. Our ranges are a US national average, so local quotes can land above or below them.
Decking
Decking is the plywood or board layer the roofing is fastened to. Damaged decking usually can’t be seen until the old roof is off, so quotes often list a price per sheet for any that needs replacing.
How to read a roofer’s quote
Get written quotes from more than one licensed, insured roofer and compare them line by line. Three things make that easier.
Labor and materials
Some quotes split labor and materials; others give one installed price. A split is easier to compare: the materials part should name the product, and labor covers tear-off, installation and clean-up.
Price per square
Most quotes are built on squares. Divide each total by its number of squares to compare quotes on the same basis, and check that the roofers measured a similar number of squares. The square count from the calculator above is a useful cross-check.
Common line items
- Tear-off and disposal: removing the old layers and hauling them away.
- Underlayment: the water-resistant layer laid over the decking before the roofing.
- Flashing: metal pieces that seal the joints around chimneys, walls, vents and valleys.
- Drip edge: metal trim along the roof edges that guides water into the gutters.
- Ridge cap and vents: the shingles along the peak and any roof vents.
- Decking repairs: usually a price per sheet, charged only for sheets that need replacing.
- Permit: a fee if your area requires one; ask who arranges it.
- Clean-up: debris removal and a nail sweep of the yard and driveway.
If a line item you expect is missing, ask whether it is included. Our figures are estimates; the roofer’s written quote is what you agree to.
More roofing calculators
All calculators →- Roof pitch calculatorRise and run to pitch, degrees and multiplier.
- Roofing calculatorRoof area and squares from your home size.
- Rafter calculatorRafter length from span, pitch and overhang.
- Roof truss calculatorHow many trusses for your building length and spacing.
- Shingle calculatorBundles of shingles from your roof area.
- Roof repair costWhat leaks, flashing and shingle repairs cost.
Questions homeowners ask
How much does a new roof cost?
Replacing an asphalt shingle roof on a 1,000–3,000 sq ft home costs about $5,500–$40,600. Roof size, pitch and material decide where yours lands, so enter your home in the calculator above, then compare the table by home size.
How much does it cost to replace a roof per square foot?
Asphalt shingles cost about $4.00–$8.00 per square foot of roof area, installed (materials and labor). Each material’s range per square foot is in the material cards above.
What is the average cost of roof replacement?
An average hides a wide spread, because roof area depends on a home’s footprint and pitch as much as its living area. The table above gives ranges for homes from 1,000 to 3,000 sq ft; the calculator gives one for yours.
How is the cost for roof replacement worked out?
We estimate your roof’s area from your living area, number of stories and pitch, then multiply by an installed price per square foot for the material. On steep roofs the labor and tear-off part costs more, and each old layer removed adds a tear-off cost. See how we estimate.
Does a steeper roof cost more to replace?
A steeper roof has more surface over the same footprint: a 12/12 roof has about 41% more area than a flat roof over the same house. Steep roofs are also slower to work on, so our estimate raises the labor and tear-off part for them. Compare 3/12 and 12/12 in the calculator above.
How we estimate
- Prices: installed cost per square foot of roof area (US national average), built from named sources, each with the date we checked it, listed on our methodology page.
- Roof area: living area ÷ stories × 1.10 for overhangs × pitch multiplier, where the multiplier is √(1 + (rise ÷ 12)²).
- Squares and bundles: squares = roof area ÷ 100; asphalt shingle bundles = squares × 3, rounded up.
- Cost: roof area × installed price per sq ft, split into materials and labor by the labor share; labor and tear-off (per sq ft for each old layer) × the steep-roof factor.
- Price per square: the installed price per sq ft × 100, the new roof only, without tear-off.
An estimate, not a quote. Get written quotes from licensed, insured roofers.